Перейти к содержимому

Поиск по сайту

Результаты поиска по тегам 'GA9050'.

  • Поиск по тегам

    Введите теги через запятую.
  • Поиск по автору

Тип публикаций


Форумы

  • Вопрос - Ответ
    • Вопрос - Ответ
  • Закрытый форум (для сотрудников сервисных центров)
    • Закрытый раздел
  • Организация сервисного центра
    • Моя мастерская
    • Организация сервисного центра
    • Обратная связь магазина Dyadko.ru
  • Статьи, полезная информация
    • Статьи
    • Калибровка, модернизация и улучшение инструмента
    • Признаки контрафактного и поддельного инструмента
  • Ремонт инструмента
    • Общая информация по ремонту
    • Перемотка и всё что с ней связано
    • Электроинструмент
    • Аккумуляторный инструмент
    • Бензоинструмент
    • Генераторы
    • Лазерный и измерительный инструмент
    • Алмазная техника
    • Пороховой монтажный инструмент
    • Пневматическое оборудование
    • Компрессорная техника
    • Сварочное оборудование
    • Тепловая техника
    • Станки и станочки
    • Автомойки высокого давления
    • Разное оборудование
    • Расходные материалы
  • Ремонтные схемы, мануалы и спецификации
    • Схемы инструментов
    • Схемы сварочного оборудования
  • Общение
    • Болталка. Вопросы не в тему
  • Барахолка
    • Куплю
    • Продаю
    • Биржа труда
  • Работа форума
    • Новости форума
    • Техническая поддержка

Категории

  • Перемотка статоров и роторов
  • Сервисные диски
  • Полезные файлы
  • Организация Сервисного Центра
  • Техническая библиотека
  • Схемы на инструмент
  • Инструкции на инструмент
    • Инструкции на инструмент Makita



Фильтр по количеству...

Найдено 1 результат

  1. Repair Angle Grinders Makita GA7050/ GA9050

    Repair Angle Grinders Makita GA7050/ GA9050 1. NECESSARY REPAIRING TOOLS 2. LUBRICATIONS Apply Makita grease SG.No.0 to the following portions designated with the black triangle to protect parts and product from unusual abrasion. 3. DISASSEMBLY/ASSEMBLY Armature, Spiral bevel gear (small), Ball bearing 6201DDW, ball Bearing 6000DDW Each model has different gears as illustrated below, and they are not interchangeable. DISASSEMBLING Disassemble Armature assembly and Small spiral bevel gear as illustrated in Figs. 2 and 3. Note: If the work is very difficult due to the seizing of Small spiral bevel gear, spray lubricant between Armature shaft and Small spiral bevel gear. And then turn and pull Armature while holding Small spiral bevel gear with pliers and a cloth. Disassemble Ball bearing 6201DDW as illustrated in Figs. 4 and 5. Disassemble Armature section as illustrated in Fig. 6. ASSEMBLING Assemble Gear housing section by setting Felt ring 16, Ball bearing 6201DDW and Retaining ring (INT) R-32 in place of Gear housing complete in accordance with the following steps. (1) Set Felt ring 16 in place as illustrated in Fig. 7 when disassembling Ball bearing 6201DDW. Assemble Ball bearing 6201DDW to Armature temporarily. After setting Ball bearing 6201DDW in place of Gear housing complete, pull off Armature. Then, fit Retaining ring (INT) R-32 into the groove of Gear housing complete to secure Ball bearing 6201DDW. (Fig. 8) Assemble Armature and small Spiral bevel gear to Gear housing complete by reversing the step shown in Fig. 3. Assemble Gear housing complete to Motor housing, And assemble Bearing box section to Gear housing complete. DISASSEMBLING Large spiral bevel gear can be disassembled as illustrated in Figs. 9, 10R and 11. Ball bearing 6202DDW can be disassembled as illustrated in Fig. 12A or Fig. 12B. ASSEMBLING Reverse the disassembling step shown in Fig. 11, 10R and 9. Note: 1) Do not deform the labyrinth ring of Spindle complete when pressfitting Spindle complete to Ball bearing 6202DDW. (Fig. 13) Putting Large spiral bevel gear on 1R165, press Spindle into arbor hole of Large spiral bevel gear with Arbor press. (Fig. 14) Shaft lock mechanism DISASSEMBLING 1) Remove Gear housing complete from Motor housing. Remove Bearing box from Gear housing complete as illustrated in Fig. 2. 2) Remove Armature from Gear housing complete as illustrated in Fig. 3. 3) Shaft lock mechanism can be disassembled as illustrated in Figs. 15 and 16. ASSEMBLING 1) Be sure to use a new Pin cap for replacement and to remove all the plastic dust on Shoulder pin 11. (Fig. 17) 2) Assemble the parts for Shaft lock mechanism as illustrated in Fig. 18. Circuit diagram Wiring diagram
×