Перейти к содержимому

Поиск по сайту

Результаты поиска по тегам 'belt sander makita 9404'.

  • Поиск по тегам

    Введите теги через запятую.
  • Поиск по автору

Тип публикаций


Форумы

  • Вопрос - Ответ
    • Вопрос - Ответ
  • Закрытый форум (для сотрудников сервисных центров)
    • Закрытый раздел
  • Организация сервисного центра
    • Моя мастерская
    • Организация сервисного центра
    • Обратная связь магазина Dyadko.ru
  • Статьи, полезная информация
    • Статьи
    • Калибровка, модернизация и улучшение инструмента
    • Признаки контрафактного и поддельного инструмента
  • Ремонт инструмента
    • Общая информация по ремонту
    • Перемотка и всё что с ней связано
    • Электроинструмент
    • Аккумуляторный инструмент
    • Бензоинструмент
    • Генераторы
    • Лазерный и измерительный инструмент
    • Алмазная техника
    • Пороховой монтажный инструмент
    • Пневматическое оборудование
    • Компрессорная техника
    • Сварочное оборудование
    • Тепловая техника
    • Станки и станочки
    • Автомойки высокого давления
    • Разное оборудование
    • Расходные материалы
  • Ремонтные схемы, мануалы и спецификации
    • Схемы инструментов
    • Схемы сварочного оборудования
  • Общение
    • Болталка. Вопросы не в тему
  • Барахолка
    • Куплю
    • Продаю
    • Биржа труда
  • Работа форума
    • Новости форума
    • Техническая поддержка

Категории

  • Перемотка статоров и роторов
  • Сервисные диски
  • Полезные файлы
  • Организация Сервисного Центра
  • Техническая библиотека
  • Схемы на инструмент
  • Инструкции на инструмент
    • Инструкции на инструмент Makita



Фильтр по количеству...

Найдено 1 результат

  1. Belt Sander Makita 9404

    Belt Sander Makita 9404 Repair < 1 > Replacing helical gear 39 complete (1) Take off abrasive belt. Remove safety cover by loosening tapping screw CT4 x 16 (2pcs.), and belt cover by loosening the same CT4 x 16. (2) Take off synchro belt 6-330. Remove gear cover by loosening tapping screw CT4 x 16 (4 pcs.). (3) Insert hex wrench 2.5 into the punched hole on helical gear 39 complete to lock driving roller. (4) Remove driving roller with box wrench 19 turning it clockwise in stead of anti-clockwise. Then, helical gear 39 complete can be separated from driving roller easily.(Helical gear 39 complete can be removed in the above mentioned way easily, because ball bearing and gear shaft are assembled to riving roller, however, without pressing.) (5) Take the reverse steps for assembling helical gear 39 complete using the following repairing tools . * No.1R219 Torque wrench (Adjust the fastening torque 6.0 - 8.5 N.m in advance for these models.) * No.1R220 Ratchet head * No.1R222 Socket adaptor Do not forget to apply Makita grease No.2 (4 g) for lubrication on helical gear 39. < 2 > Replacing helical gear 10 (1) Hold helical gear 10 with the following repairing tools. * 1R041 Copper plate * 1R082 Vise (2) Remove pulley 9.5-46.0 with box wrench 19 by turning it anti-clockwise. (3) Take reverse steps for assembling helical gear 10 using the following repairing tools. * No.1R219 Torque wrench (Adjust the fastening torque 6.0 - 8.5 N.m in advance for these models.) * No.1R220 Ratchet head * No.1R222 Socket adaptor Be careful not to damage the new helical gear 10 with vise, when assembling. < 3 > Replacing armature (1) Remove belt cover by loosening tapping screw CT4 x 16 (1 pc.). Take off synchro belt 6-330. (2) Separate frame complete from motor housing by loosening tapping screw 4 x 30 (5 pcs.) and the same CT4 x 16 (1 pc.). (3) Remove motor cover from motor housing by loosening tapping screw 4 x 18 (4pcs.). (4) Take off carbon brush. (5) Remove fan 76 and hex nut M6 by turning them clockwise from armature. And remove armature from motor housing. (6) Take the reverse steps for assembling armature. (It is enough that fan 76 can be slightly fastened with hand .) Circuit diagram Model 9903, 9920 and 9404 (equipped with controller) < Note > Noise suppressor is not used in some country. Wiring Model 9903, 9920 and 9404 (equipped with controller)
×